Decking Calculator

Plan the materials for a timber or composite deck. Enter the deck length and width, the actual board width and gap, the board length you can buy and the joist spacing, and the calculator works out rows of boards, boards per row, total boards with waste, the linear length of decking, the number of joists and an estimate of deck screws.

By Rashid MehmoodLast updated and reviewed Free, no sign-up

Deck calculator

ft
ft
in
in
ft
in
%
–

How to use the decking calculator

  1. Measure the deck. Enter the length along the boards and the width across them. Boards usually run parallel to the house.
  2. Enter board size and gap. Use the actual board width (a 6 in nominal board is 5.5 in actual) and the gap the manufacturer recommends.
  3. Enter board length and joist spacing. Choose the stock length you will buy and the joist centres (16 in, 400 mm or 450 mm are common).
  4. Add waste. Around 10% covers end trims, splits and defects.
Embed this calculator

Paste this iframe on your own site. The embed view already includes a visible “Calculator by CalcTen” credit, which must stay visible. See the developers page for the conditions.

A deck looks simple, but the material list has many parts. This calculator focuses on the parts that are easy to count and expensive to get wrong: the decking boards, the number of joists and the screws. It works in feet and inches or metres and millimetres and pre-fills common board and joist sizes for your region.

The formula explained

Rows = ⌈ Deck width ÷ (Board width + Gap) ⌉
Boards per row = ⌈ Deck length ÷ Board length ⌉
Boards = ⌈ Rows × Boards per row × (1 + Waste ÷ 100) ⌉
Joists = ⌊ Deck length ÷ Joist spacing ⌋ + 1
Screws = Rows × Joists × 2

Board length. Boards per row is the number of stock lengths needed to cover the deck length, so a 4.8 m deck with 3.6 m boards needs two boards per row. Joints should land on a joist and be staggered between rows; the waste allowance helps cover offcuts that are too short to reuse.

Joists. The joist count includes one at each end. It assumes joists run across the boards for the full deck width.

Worked examples

Example 1: US backyard deck

A 16 × 12 ft deck with 5.5 in boards, 3/16 in gaps, 16 ft boards and 16 in joist centres, 10% waste:

  1. Rows: 144 in ÷ 5.6875 in = 25.3 → 26 rows.
  2. Boards per row: 1; with waste: 29 boards.
  3. Linear decking: 26 × 16 = 416 ft.
  4. Joists: 192 ÷ 16 + 1 = 13 joists, each 12 ft.
  5. Screws: 26 × 13 × 2 = 676.

Example 2: UK garden deck

A 4.8 × 3.6 m deck, 144 mm boards, 5 mm gaps, 3.6 m boards, 400 mm joists, 10% waste:

  1. Rows: 3.6 ÷ 0.149 = 24.2 → 25 rows.
  2. Boards per row: 4.8 ÷ 3.6 → 2; total with waste: 55 boards.
  3. Linear decking: 120 m; joists: 13; screws: 650.

Example 3: Australian hardwood deck

A 5.4 × 4 m deck, 140 mm boards, 5 mm gaps, 5.4 m boards, 450 mm joists:

  1. Rows: 4 ÷ 0.145 = 27.6 → 28 rows, one board each; with waste 31 boards.
  2. Linear: 151.2 m; joists: 5.4 ÷ 0.45 + 1 = 13; screws: 728.

Picture framing and breaker boards

A picture-frame border runs boards around the edge of the deck, mitred at the corners, so no cut ends are visible. Count the border separately: its length is the deck perimeter, and the field boards then cover a slightly smaller area (deck size minus two border widths in each direction). A breaker board is a single board run across the middle of a long deck so that field boards butt against it rather than joining end to end. Both look good but need extra blocking or doubled joists underneath, and both increase waste; allow 15% rather than 10%.

Regional notes: US, UK, Australia and Canada

United States. Deck boards are usually 5/4 × 6 (about 1 × 5.5 in actual) or 2 × 6 lumber, in 8–20 ft lengths. Many jurisdictions base deck construction on the IRC and publish prescriptive deck guides covering ledger attachment, joist spans and footings. Permits are often required.

United Kingdom. Softwood decking is commonly 120–150 mm wide in 2.4, 3.6 and 4.8 m lengths. Joists are typically at 400 mm centres. Planning permission is usually needed for decking more than 0.3 m above the ground; the Planning Portal explains the rules for England.

Australia. Hardwood decking in 70–140 mm widths is common, sold by the linear metre in random or set lengths. Joist spacing of 450 mm is typical for 19 mm hardwood; check AS 1684 span tables and state requirements.

Canada. Practice is similar to the US, with provincial codes and municipal permits. Pressure-treated SPF and cedar are common.

Tips and common mistakes

  • Use actual sizes. A nominal 6 in board is about 5.5 in wide.
  • Plan joints. Stagger butt joints between rows and land each on a joist; double up joists at joints if needed.
  • Check spans. Joist size and beam spans must follow your local tables.
  • Allow for the frame. Rim joists, ledgers, beams, posts and blocking are separate items; the board foot calculator can total timber volume.
  • Footings. Concrete for post footings can be estimated with the concrete calculator.
  • Ventilation and drainage extend deck life, especially near the ground.

Building steps up to the deck? Use the stair calculator. Adding a privacy screen or boundary? Try the fence calculator.

Frequently asked questions

How many deck boards do I need?

Divide the deck width by the board width plus gap to get rows, multiply by the boards needed per row, and add waste. A 16 × 12 ft deck with 5.5 in boards and 3/16 in gaps needs 26 rows of 16 ft boards, or 29 boards with 10% waste.

What gap should I leave between deck boards?

Follow the manufacturer. Timber decking is often gapped about 3–6 mm (1/8–1/4 in) depending on moisture content; composite boards usually have a specified gap and use hidden clips.

What joist spacing do I need?

16 in (about 400 mm) centres is common for timber decking; composite boards and diagonal layouts often need 12 in (300 mm) centres. Check board and code requirements.

How many screws do I need for decking?

Two screws per board at every joist is standard for face-fixing. The calculator multiplies rows × joists × 2. Hidden fastening systems use clips instead.

Which way should deck boards run?

Usually parallel to the house and across the joists. Diagonal boards look striking but need closer joists and more waste.

Does this calculator size joists and beams?

No. Joist size, span, beams, posts and footings depend on loads and local span tables. Use your local code, a span table or an engineer.

How much waste should I allow?

About 10% for straight boards, 15% for diagonal layouts or picture-framed edges.

Do I need permission to build a deck?

Rules vary. Many US and Canadian towns require a permit for decks above a certain height or attached to the house; in the UK, raised platforms over 0.3 m usually need planning permission.

Sources and references

About this calculator

Written and maintained by Rashid Mehmood, founder of CalcTen. The formulas are unit-tested against hand-worked examples, and the content is reviewed whenever product sizes or guidance change. Last updated and reviewed 1 November 2026. See our editorial policy. If you spot a mistake, report it.

Results are estimates for planning and ordering. Always check product labels, supplier advice and local building codes, and consult a qualified professional for structural work. Read the disclaimer.

Calculator by CalcTen — free online calculators.