Ohm’s Law Calculator
Enter any two of voltage (V), current (I), resistance (R) and power (P), with at least one of V, I or R, to find the other quantities from Ohm’s law and the power identities. The default example is 12 volts and 2 amperes, which gives 6 ohms and 24 watts. Use this for a simple DC circuit or as an RMS snapshot. It is not a substitute for the [voltage drop calculator](/home-diy/voltage-drop-calculator/) when the question is how much voltage is lost along a cable.
Ohm's law calculator
On this calculator: Ctrl+Enter copies the result, Shift+Alt+L copies a link to the current inputs, Shift+Alt+R resets, Shift+Alt+P opens Print / Save PDF. These shortcuts do not run while you type in a field, except Ctrl+Enter.
Saved results on this device
Stored only in this browser, not on our servers.
How to use the ohm’s law calculator – voltage, current, resistance and power
- Enter two known values. Fill any valid pair: V and I, V and R, I and R, P and V, P and I, or P and R. Leave the other two blank.
- Check the units. Voltage in volts, current in amperes, resistance in ohms, power in watts.
- Solve. The calculator returns the two unknowns and restates the two inputs.
- Read the diagram. The figure shows the relationship among V, I, R and P for the values you entered.
Formulae
V = I × R · I = V ÷ R · R = V ÷ I
P = V × I = I²R = V² ÷ R
Any two of these quantities (with at least one of V, I or R) determine the other two in a simple resistive circuit.
Worked examples
12 V and 2 A (default). R = 12 ÷ 2 = 6 Ω. P = 12 × 2 = 24 W. You can check the same power as I²R = 4 × 6 = 24, or V²/R = 144 ÷ 6 = 24.
A 60 W bulb on 120 V. I = 60 ÷ 120 = 0.5 A. R = 120² ÷ 60 = 240 Ω.
A 10 Ω resistor dissipating 40 W. I = √(40 ÷ 10) = 2 A. V = 2 × 10 = 20 V.
Use cases and common mistakes
Use the tool to check a load, a resistor, or a simple DC supply. Common mistakes include mixing peak and RMS values on AC, entering milliamps as amps, and using this page to size a long cable — that is the job of the voltage drop calculator. Power-only conversions between amps and watts, when voltage is already known, are also covered by the amps to watts calculator. Room cooling capacity is a different question, on the BTU calculator.
Limitations
The model is a single lumped resistance. It does not include reactance, power factor, temperature coefficients, or three-phase factors. Results are general information, not a wiring design and not a safety approval.
Frequently asked questions
What is Ohm’s law?
V = I × R, where V is voltage in volts, I is current in amperes and R is resistance in ohms. Power in a simple resistive circuit is P = V × I, which also equals I²R and V²/R.
What do 12 V and 2 A give?
R = V ÷ I = 12 ÷ 2 = 6 Ω, and P = V × I = 24 W. That is the default example.
Can I enter only power and one other value?
Yes. From P and V you get I = P ÷ V and R = V² ÷ P. From P and I you get V = P ÷ I and R = P ÷ I². From P and R you get I = √(P ÷ R) and V = I × R. Entering only P, or entering three conflicting values, is rejected.
Does this work for AC?
For a purely resistive AC load, you can use RMS voltage and RMS current in the same formulae. Power factor, reactance and three-phase systems are not modelled. Do not use a DC result as a three-phase design.
How is this different from the voltage-drop calculator?
Ohm’s law solves a concentrated resistance. Voltage drop along a cable also depends on length, conductor size and material. Use the [voltage drop calculator](/home-diy/voltage-drop-calculator/) for that job, and this page for a single V–I–R–P relationship.
What if I enter values that disagree?
If you fill more than two fields and they are inconsistent, the calculator will not invent a compromise. Enter exactly two knowns.
Is this an electrical design or a safety certificate?
No. It is arithmetic for a simple circuit. Cable sizing, protection and installation must follow the applicable electrical code and a qualified person.
Related calculators
Voltage Divider Calculator – Vin, R1, R2 and Optional Load
DC voltage divider with optional load: Vout from Vin, R1 and R2.
Voltage Drop Calculator
Volts and percent drop for AWG or mm² cable.
Amps to Watts Calculator
Amps to watts (and watts to amps) for DC, AC and three-phase.
Scientific Calculator – Trig, Logs, Powers and Roots
Trigonometry, logarithms, powers, roots and factorials in degrees or radians, with a printable tape of the working.
BTU Calculator – Room Air Conditioner Size
Room AC size from the ENERGY STAR chart, with shade, sun, people and kitchen adjustments.
Percentage Calculator – What Is X% of Y?
X% of Y, X is what % of Y, and X is Y% of what number.
Sources and references
About this calculator
Written and maintained by Rashid Mehmood, founder of CalcTen. The formulas are unit-tested against hand-worked examples, and the content is reviewed whenever product sizes or guidance change. Last updated and reviewed 15 November 2026. See our editorial policy. If you spot a mistake, report it.
Results are estimates for planning and ordering. Always check product labels, supplier advice and local building codes, and consult a qualified professional for structural work. Read the disclaimer.