Voltage Divider Calculator
Enter an input voltage Vin, the upper resistor R1, the lower resistor R2, and, if you have one, a load RL in parallel with R2. The calculator returns Vout, the current through R1, and the effective lower resistance. The default is 12 V with R1 = 1 kΩ and R2 = 2 kΩ, which divides to 8 V unloaded. With a load, R2′ is the parallel combination of R2 and RL. This is a DC resistive divider, not a regulator design, and it complements the Ohm’s law calculator on this site.
Voltage divider calculator
On this calculator: Ctrl+Enter copies the result, Shift+Alt+L copies a link to the current inputs, Shift+Alt+R resets, Shift+Alt+P opens Print / Save PDF. These shortcuts do not run while you type in a field, except Ctrl+Enter.
Saved results on this device
Stored only in this browser, not on our servers.
How to use the voltage divider calculator – vin, r1, r2 and optional load
- Enter Vin, R1 and R2. R1 sits between Vin and the output node; R2 sits between the output node and ground.
- Optionally enter a load RL. Leave RL blank for the unloaded divider. A positive RL is taken in parallel with R2.
- Read Vout and the current. Vout = Vin × R2′ / (R1 + R2′). The current through R1 is Vin / (R1 + R2′).
- Check with Ohm’s law. The Ohm’s law calculator relates V, I, R and P for a single resistor. This page is the two-resistor divider.
The unloaded and loaded formulas
An unloaded resistive divider is two resistors in series across Vin. The output is taken from the join. By the series voltage rule,
Vout = Vin × R2 / (R1 + R2).
The same current Vin / (R1 + R2) flows through both resistors. For 12 V, 1 kΩ and 2 kΩ that current is 4 mA and Vout is 8 V, which you can also check as I × R2.
When a load RL is attached at the output, it sits in parallel with R2. The lower leg becomes R2′ = (R2 × RL) / (R2 + RL), and the same formula is used with R2′ in place of R2. Vout falls, and the current through R1 rises. Leaving RL blank keeps the unloaded case; a zero or negative RL is ignored as “no load.”
This is not a model of a linear regulator, a zener clamp, or an op-amp reference. Those circuits use a divider as a sense network, but they are not this equation. Power dissipated in each resistor is I²R (or V²/R) if you want a hand check; the page reports I and Vout so you can finish that step. The voltage-drop calculator is for cable runs, not a divider, and the resistor colour-code calculator reads the bands on a physical resistor.
The diagram is a simple series pair with Vout taken at the midpoint. Print / Save PDF keeps Vin, the resistances and Vout. The 12 V, 1 kΩ, 2 kΩ → 8 V case is unit-tested. Report a mistake from the about box if a loaded result disagrees with a parallel-then-divide hand calculation.
Frequently asked questions
What is Vout for 12 V, R1 = 1 kΩ and R2 = 2 kΩ?
Unloaded, Vout = 12 × 2 / (1 + 2) = 8 V. The current is 12 / 3,000 = 4 mA. That is the default example.
What changes when I add a load?
R2′ = R2 ∥ RL = (R2 × RL) / (R2 + RL), and Vout falls because the lower leg is then smaller than R2 alone.
Does the order of R1 and R2 matter?
Yes. R1 is the upper resistor (from Vin to the output). Swapping R1 and R2 swaps the ratio.
Is this a voltage regulator?
No. A resistive divider sags under load and wastes power in R1 and R2. Use a regulator when you need a stiff supply; this page only does the divider arithmetic.
Can I use it for AC or a reactive divider?
The formula here is DC (or the resistive part of a network). Capacitive or inductive dividers need impedances, which are not on this page.
How does this relate to Ohm’s law?
Ohm’s law is V = I × R. A divider is two resistances in series (or series-plus-parallel with a load) across Vin. The Ohm’s law calculator is the single-component counterpart.
What units should I use?
Volts and ohms (then current is in amperes). You can enter 1000 or 1e3 for 1 kΩ; prefixes are not parsed as text.
Related calculators
Ohm’s Law Calculator – Voltage, Current, Resistance and Power
Solve V, I, R and P from any valid pair, using V = I × R and P = V × I.
Voltage Drop Calculator
Volts and percent drop for AWG or mm² cable.
Resistor Color Code Calculator – 4-Band and 5-Band
Decode 4-band and 5-band resistor colours to ohms and tolerance (IEC 60062).
Amps to Watts Calculator
Amps to watts (and watts to amps) for DC, AC and three-phase.
Scientific Calculator – Trig, Logs, Powers and Roots
Trigonometry, logarithms, powers, roots and factorials in degrees or radians, with a printable tape of the working.
Sources and references
About this calculator
Written and maintained by Rashid Mehmood, founder of CalcTen. The formulas are unit-tested against hand-worked examples, and the content is reviewed whenever product sizes or guidance change. Last updated and reviewed 15 November 2026. See our editorial policy. If you spot a mistake, report it.
Results are estimates for planning and ordering. Always check product labels, supplier advice and local building codes, and consult a qualified professional for structural work. Read the disclaimer.